ZP19072 WoodTek Slatted Portable Puppy Fence Kit (2 Pack) (Cedar)

Important Safety Notes:

• Check the inside of the larger pieces in your box for other materials packed inside.
• When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching.
• We recommend an area approximately 5' x 8' for unobstructed assembling.
• You should not need to use excessive force when assembling components.

Returns:
If you wish to return your product, please contact us first — we can often help resolve the issue right away.
If a return is still necessary, it must be initiated with the retailer where the product was purchased.

Need Help or Replacement Parts?

If you need replacement parts, assembly assistance, or have questions about the product, our customer service team is ready to help:

• Website: https://parts.nychbrands.com
• Email: support@zippity-outdoor.com
• Phone: 704-892-5222 or 877-234-6196

Customer service agents are available 9am–5pm EST, Monday–Friday.

For Quick Assistance:

• Have reference item number ZP19072/ZP19073
• Provide the specific part name
• Include the batch lot number found on the end of the box

A — Rail End Cap (8)

(4 Installed, 4 Loose)

B — Portable Feet (4)

⅞" x 1½" x 12"

C — Silicone No-Scratch Pad (8)

D — Top Rail (2)

1½" x 1½" x 44"

E — Bottom Rail (2)

1½" x 1½" x 44"

F — Post (4)

⅞" x 1½" x 22¼"

G — Center Support (2)

⅝" x 1" x 21¼"

H — Slats (18)

¼" x 1¼" x 42⅞"

I — Connector Pin (4)

(4 Installed, 4 Loose)

J — Locking Pin (4)

K — ¾" Self-Drilling Stainless Steel Screw (16)

L — 1½" Self-Drilling Stainless Steel Screw (8)

• Lay out all parts and confirm all pieces are present before beginning assembly.

• Slide (9) Slats (H) into the routed holes of the Center Support (G) until the center support sits in the middle of the slats.

1. Slide the slats into the routed holes in one of the Posts (F).
2. Slide a second end post over the slats.

Note: This side of the post up.

• Identify the Top Rail (D) and the Bottom Rail (E) as shown below.
• Insert two loose Rail End Caps (A). Make sure they are oriented as illustrated.

Note: The top rail will have no cut hole here.

• Slide the top rail over the tops of the posts until the pre-drilled holes in the posts and the top rail align.
• Drive (2) total ¾" Self-Drilling Stainless Steel Screws (K) into the pre-drilled holes in the top rail.

• Slide the bottom rail over the bottoms of the posts until the pre-drilled holes in the (2) posts and the bottom rail align. Ensure the middle post inserts into the hole in the bottom rail.
• Drive (2) ¾" self-drilling stainless steel screws (K) into the pre-drilled holes in the bottom rail.

• Turn the panel to the other side and drive (4) total ¾" self-drilling stainless steel screws (K) through the pre-drilled holes in the top and bottom rail.

• Identify the Portable Feet (B). Set aside (4) of the Silicone No-Scratch Pads (C).
• Remove the adhesive cover from the pads and stick two pads on the far ends of the underside of each foot as shown below.

• Take one of the portable feet and slide the notched end over the underside of the bottom rail.
• Align the foot pre-drilled holes with the bottom rail pre-drilled holes and drive (2) 1½" Self-Drilling Stainless Steel Screws (L) through the pre-drilled holes in the underside of the portable foot.
• Repeat this process on the other side of the fence panel.

• Repeat steps 3–4 to assemble the second fence panel.

• Connect the two fence panels using the Connector Pins (I) as shown below.
• In-Line Application: Insert Connector Pins (I) through the aligned holes at the top and bottom of the adjoining posts.

• Corner/Angled Application: Connect the two fence panels using the Connector Pins (I) as shown below.

• Secure the connector pins with the Locking Pin (J).

• Email: support@zippity-outdoor.com
• Phone: 704-892-5222 or 877-234-6196
• Text: 980-580-6508